g. Cherry st. Kiev 29 (warehouse)

g. Киев ул. Dovbusha 37 (office)

zskzabor@gmail.com
 
The cart is empty
Отсутствует перевод страницы

Компания ЗСК стремится быть лучшей в Украине компанией по подбору, комплектации и монтажу объектов системами ограждений, освещения и видеонаблюдения. Мы предоставляем полный спектр услуг: проектирование, производство, комплектация, монтаж и наладка.

О Нас:

- квалифицированный персонал;

- наличие собственной материально-технической базы;

- работаем на всей территории Украины;

- используем ПО (AutoCad, АВК и т.д.);

- защита периметра "под ключ" (ограждение, освещение, видеонаблюдение);

- работаем с организациями всех форм собственности.


Наши объекты:

- спортивные площадки (футбольные поля, баскетбол, вокраут и другое);

- детские площадки;

- электростанции;

- фермерские хозяйства;

- заводы;

- режимные объекты ;

- не дорогие заборы для дачи;

- ограждение клумб;


Установка забора из сетки

Монтаж ограждений производится с помощью анкерного крепления или путем бетонирования опорных столбов в грунт. Стандартный размер фундаментов для бетонирования опор имеет следующие размеры:

- столб ограждения: диаметр от 200мм, глубина 700мм;

- опорный столб для калитки/ворот: диаметр 250-300мм, глубина 800мм.

В стоимость включены расходные материалы (анкера, цемент, щебень, песок), в зависимости от объема монтажа и необходимости предоставления дополнительных услуг, таких как резка асфальта, демонтаж старого ограждения, активное хранение и т.д. стоимость за метр погонный может изменяться прайс установка ограждения из сетки .

Минимальный объем необходимый для выезда бригады на объект 20 м.п..

This email address is being protected from spambots. You need JavaScript enabled to view it.

Строительство ограждений для спортивных площадок

Ограждение для спортивных площадок должно выдерживать ударные нагрузки, правильное проектирование и монтаж поможет избежать ежегодных дорогостоящих ремонтов.

Мы рекомендуем еще на этапе проектирования ограждения для футбольных полей , использовать сварную сетку ПРОМ 6/5/6 и дополнительно защитную сетку, которая будет гасить энергию удара мяча. Прайс установка ограждения из сетки

This email address is being protected from spambots. You need JavaScript enabled to view it.

Монтаж спирального барьера безопасности Егоза

При монтаже барьера безопасности необходимо использовать прочные и качественные материалы, и удержаться от использования «экономных» вариантов. Важно понимать, что за экономией скрывается упрощенная конструкция элементов, которая попросту гнется еще на этапе монтажа и не сможет исполнять своей функции. Мы рекомендуем использовать Егозу с сердечником не менее 2,5мм, направляющую проволоку того же диаметра и кронштейны которые можно качественно закрепить на ограждении и при натяжке СББ они не будут гнуться. прайс монтаж Егозы

This email address is being protected from spambots. You need JavaScript enabled to view it.
PRICE:

1. From the factory, without intermediaries!

2. Discounts for volume %

3. Promotions and sales - here

4. We cooperate: customers / contractors / designers

5. Expanding the dealer network

PAYMENT:

1. Cash (pickup)

2. Cashless ( receive an invoice with VAT )

3. Visa and MasterCard

4. Overlaid

1. Pickup (right and left banks)

2. Kiev - from UAH 500. (14 UAH / km Region)

3. Ukraine "Nova Poshta", "Delivery", "SAT"

Вы смотрели:

mesh plastering
UAH 786,00 грн each
29 5 5 0
sliding gate automation - Nice ROX kit up to 1000 kg drive + remote control 2pcs rox1000 12 months warranty ✔ sliding gate automation Italy
UAH 12 463,49 грн each
1 5 5 0
avtkkk
UAH 717,30 грн each
1 5 5 0
Mesh for cells
UAH 1 675,20 грн each
1 0 5 0
Fence mount standard for mesh fencing
UAH 15,00 грн each
35 4.91429 5 0
100x100 GOST road mesh 3mm wire ВР1 mesh is used for masonry: brick, gas blocks, foam blocks, reinforcing concrete, floors and screeds road mesh 100x100x3 price ✔ masonry mesh
UAH 44,00 грн per unit for buying at least 120
1 5 5 0

Installing the fence

Setting up a fence You can install the welded mesh fence yourself or contact the ZSK specialists. It is easier, of course, to contact the specialists, but if you decide to install the fence yourself, you must carefully read the instructions, stock up on the necessary tools and gather a team of like-minded people.

Efficiency of installation largely depends on correct planning: the better you plan everything, the easier the installation process will be.

I. PLANNING

1. Planning a plot:

fence installation rates - measure the perimeter;

- we draw up a fence scheme taking into account the landscape and legislation;

- we determine the height, taking into account the landscape (from 0.9m to 4m);

- select the type of sections "Eco", "Classic", "Sport", "Prom";

- select the pillars and attachments to them;

- according to the input data, we form a list of components (the manager of the ZSK company will help).

2. We calculate the necessary consumables:

- we determine the number of anchors (if installation on ready-made concrete *);

- we determine the required amount of cement, sand and crushed stone (if installation into the ground with subsequent concreting);

- we buy the necessary screws and rivets;

3. Stock up on the right tool:

fence installation tool - hammer drill (installation on concrete *);

- a drill for soil with a diameter of 200mm or a shovel;

- screwdriver;

- wrench;

- threaded riveter;

- electrical extension cord;

- generator (if there is no power source);

- concrete mixer or mixer;

- level;

- mounting plates;

- lanyard;

- a set of tools (hammer, crowbar, etc.)

- welding machine (if necessary);

- stairs;

4. We gather a team of like-minded people:

- normal installation (at least 2 people);

- complex installation (at least 4 people);

* Ball of concrete at least 16cm.

After you have planned everything, ordered materials, collected the tool and like-minded people, it's time to start installing.

INSTALLATION IN THE GROUND (with concreting)

1. We mark the site and fix the marking cord.

2. We place two pillars on a flat surface and fix the section to them; we assemble them in the immediate vicinity of the place where the installation starts:

ZSK fence section - fastening of sections to posts with built-in nuts is done using a "hexagon",

- fastening of sections to posts with through holes is made using a key-head 10 ",

- fastening of sections to posts by means of concealed installation is carried out using a key-head 14 "

3. We drill holes in the soil of the required diameter and depth (depth 600-800mm, diameter 200-300mm). The distance between the holes corresponds to the width of the section.

holes for a fence post
4. We install the assembled section into the prepared holes in the ground.

first installed section
5. We mark and drill the next holes at a distance of 2517mm (2.5m section), and 3017mm (3m section).

6. On a flat surface, we assemble a structure from one section and one pillar.

one section with a pillar - fastening of sections to posts with built-in nuts is done using a "hexagon",

- fastening of sections to posts with through holes is made using a key-head 10 ",

- fastening the sections to the posts in a hidden way installation is carried out using a key-head 14 "

7. We install the assembled structure into the prepared hole (item 5), and attach it to the previously installed sections (item 4). When installing on poles with a built-in nut, 2 people are required, when installing on poles with through fastening - 3 people.

8. We repeat steps 5, 6 and 7 until the perimeter is completely installed.

installation of the fence from the mesh
9. We level the outermost sections on one side of the fence and fix them with mounting strips.

10. We stretch the marking line between the extreme posts of one side, check the horizon.

11. We expose intermediate sections along the cord (clause 10) and fix with mounting plates.

12. Repeat steps 9, 10 and 11 for each side of the perimeter.

13. After the entire fence is level and fixed with mounting strips, we knead the concrete.

14. Pour the ready-made concrete into the holes with the pillars.

15. We wait 24 hours, after which we remove the mounting strips. Congratulations, you've installed the fence!

Tips:

The installation of a fence kit with poles with embedded nuts is easier and faster, less labor costs.

Fences with through fastenings can be additionally equipped with "anti-vandal nuts", which will make it almost impossible to unauthorized dismantling (theft).

INSTALLATION ON A FOUNDATION (bases with anchors)

1. We mark the area and fix the marking cord.

2. We fix on all pillars "supporting bases", not complete fixation (leave) (in some cases, it is possible to manufacture pillars with the possibility of fixing to concrete).

3. On a flat surface we place two pillars and fix the section to them, we assemble them in the immediate vicinity of the place where the installation starts:

- fastening of sections to posts with built-in nuts is carried out using a "hex" on the front side of the post,

- fastening of sections to posts with through holes is carried out using a key-head 10 ', on the back side of the post.

4. Install the assembled section with two pillars on the foundation and mark the holes.

5. We drill holes (diameter 10mm) in the concrete base according to the marking.

6. Install the assembled section and fix the “base supports” with anchors to the concrete.

7. Place one pillar on a flat surface and fix the section to it, assemble it in the immediate vicinity of the place where the installation starts:

- fastening of sections to posts with built-in nuts is carried out using a "hexagon" on the front side of the post,

- fastening of sections to posts with through holes is carried out using a key-head 10 ', on the back side of the post.

8. Install the assembled section with one pillar on the foundation and mark the holes.

9. We drill holes (diameter 10mm) in the concrete base according to the markings (p.8).

10. Install the assembled structure (item 7) and fasten it to the pre-installed sections (item 6) and anchors to the concrete. When mounting on poles with a built-in nut, 2 people are required, when mounting on poles with through fastening - 3 people.

11. Repeat steps 7, 8, 9 and 10 until the perimeter is completely set.

12. We level the outermost sections on one side of the fence, and fix the "base supports" to the post.

13. Pull the marking line between the extreme posts of one side, check the horizon.

14. We set the intermediate sections along the cord (item 10) and clamp the "base supports" to the post.

15. Repeat steps 12, 13 and 14 for each side of the perimeter.

16. Congratulations, you've installed the fence!